You are here: Home Products TOA

VM-2240


VM-2240
 


The VM-2240 is a multifunctional amplifier that can be mounted in an EIA-Standard equipment rack (3-unit size). The unit comes with 4 audio inputs including the background music input, and the speaker output section which has an internal attenuator and 5-zone selector. It permits not only general-purpose broadcast, but also Emergency Broadcast based on the EN60849 Standard which gives pre-recorded voice instructions(*1) in the emergency situation. Broadcast can be made from an optional RM-200M Remote Microphone as well as from the amplifier, and can be remotely controlled from external equipment. In addition, for 100 V/42 Ω application the unit features the surveillance function(*2) which automatically checks the system for failures. (*1) An optional EV-200M Voice Announcement Board is required. (*2) An optional SV-200MA Surveillance Board is required.






Specifications


Power Source AC: 230 V, 50/60 Hz
DC: 24 V/15 A, M3.5 screw terminal, Barrier distance: 8 mm (0.31"),
Applicable cable diameter: AWG22 - AWG14
Power Consumption on AC Mains With no signal present: 54 W
Under normal operating conditions according to
EN60065: 1998 sec. 4.2: 255 W
With rated output signal: 549 W
Current Consumption on 24 V DC Power Input With no signal present: 1 A
Under normal operating conditions according to
EN60065: 1998 sec. 4.2: 5 A
With rated output signal: 14 A
Rated Output 240 W
Output Voltage /Impedance 100 V/42 Ω, 70 V/21 Ω, 50 V/10 Ω
(selectable by the internal wiring change)
Frequency Response 50 Hz - 16 kHz
Distortion 1 % or less
Signal-to-Noise Ratio 60 dB or more
Tone Control Bass: 100 Hz ±10 dB, Treble: 10 kHz ±10 dB
(Inputs 1 - 3 and BGM individually adjustable.)
Remote Microphone /Expansion Amplifier Connection 2 RJ45 female connectors for connecting the RM-200M Remote
Microphone and the VM-2120 or VM-2240 unit used as an
expansion amplifier.
Maximum distance: 800 m (874.89 yd) in total
Link cable: Category 5 Shielded
Number of connectable RM-200M's: Up to 4
Twisted-Pair straight cable (TIA/EIA-568A standard)
Input Inputs 1 - 3: -60 dB(*3) (MIC)/-10 dB(*3) (LINE) (changeable),
600 Ω, electronically balanced(*4),
combined XLR connector (female)/phone jack
(Only Input 1 is additionally equipped with DIN
connector(*5).)
Telephone paging input: Push-in terminal block(*6)
Voice sound: -10 dB(*3), 10 kΩ, electronically-
balanced input with shield terminal(*4)
Control: No-voltage make contact input,
open voltage: 3.3 V DC,
short-circuit current: under 1 mA
BGM 1 - 2: -20 dB(*3), 10 kΩ, RCA pin jack, monaural (internally mixed)
Power amplifier input: 0 dB(*3), 10 kΩ, RCA pin jack
External speaker line input: 100 V line, for All-Zone Broadcast
(This input is selected when the "Unit's
broadcast cutoff" control is activated.)
Output Speaker output: Plug-in screw connector(*7)
5-zone selector with attenuator (all zones simultaneously
selectable)
Direct speaker line output: Direct output from the power amplifier
output transformer (attenuator bypassed),
Plug-in screw connector(*7)
Line output: 0 dB(*3), 10 kΩ, RCA pin jack
Recording output: 0 dB(*3), 10 kΩ, RCA pin jack
Preamplifier output: 0 dB(*3), 10 kΩ, RCA pin jack
Control Input For controlling Inputs 1 - 3, Push-in terminal block
No-voltage make contact input, open voltage: 3.3 V DC,
short-circuit current: 1 mA or less
Control Input and Output D-sub connector (25-pin, female)
Input: No-voltage make contact input, open voltage: 3.3 V DC,
short-circuit current: 1 mA or less
Output: Open collector output, withstand voltage: 30 V DC,
control current: 10 mA or less
(1) External control input
Activation of messages(*8)
Activation of power
Activation and stop of Emergency Broadcast
Unit's broadcast cutoff
(when activated by an external emergency equipment)
(2) Status output
Irregularity of communications with the Remote Microphone and
an expansion amplifier
AC power condition
DC power condition
Irregularity of the sound source of the Voice Announcement Board
Failure (FAULT) indication on
Power switch on
External Attenuator Control Output Plug-in screw connector(*7), relay, no-voltage make contact output,
transfer type, withstand voltage: 30 V DC, 125 V AC,
contact current: 7 A (DC) or less, 7 A (AC) or less
Surveillance Input and Output(*9) D-sub connector (25-pin, female)
Input: No-voltage make contact input, open voltage: 3.3 V DC,
Output: Open collector output, withstand voltage: 30 V DC,
Power Supply 24 V DC/0.1 A, for supplying power to an optional Amplifier Control
Unit RU-2001/-2002, push-in terminal block(*6)
Chime Tone Built-in chime: 2-tone chime/2-tone chime (fast repeat)/4-tone
chime (Up)/Single-tone chime/4-tone chime (Up &
Down)/Gong/off
Voice Announcement Board sound source: Pre-recorded chime(*8)
Function Two units stacking (VM-2120 or VM-2240)
Emergency broadcast (sequential control)
Broadcast priority control
Surveillance (failure detection) function(*9)
Power supply to only one Remote Microphone (RM-200M)
Line resistance: 40 Ω (one way) or less
Operating Temperature 0 ℃ to +40 ℃ (32 %%dF to 104 %%dF)
Finish Panel: ABS resin, dark gray (PANTONE 447C or its equivalent), paint
Case: Steel plate, dark gray (PANTONE 446C or its equivalent), paint
Dimensions 419 (W) × 143.3 (H) × 355.7 (D) mm (16.5" × 5.64" × 14")
Weight 14.5 kg (31.97 lb)
Accessory Power cable (2 m (6.56 ft)) ……1, Name label ……1, Volume cover ……4
Miniature type time-lag fuse T3.15 A ……1
Option Rack mounting bracket: MB-36
Input transformer: IT-450
Voice announcement board: EV-200M
Surveillance board: SV-200MA

(*3) 0 dB= 1 V
 

Facebook Elsiscom

Visitors Counter

mod_vvisit_countermod_vvisit_countermod_vvisit_countermod_vvisit_countermod_vvisit_countermod_vvisit_counter
mod_vvisit_counterToday266
mod_vvisit_counterYesterday5540
mod_vvisit_counterThis week10300
mod_vvisit_counterLast week4150
mod_vvisit_counterThis month29880
mod_vvisit_counterLast month31424
mod_vvisit_counterAll days642643

We have: 4 guests, 10 bots online
Your IP: 54.211.180.175
 , 
Today: Oct 23, 2014